revisions lt description date approved a added approved source of supply. revised table iv . added 6.4 . removed table from 3.3.1 . 1 7 april 2008 michael a. radecki b added an approved source of supply . 22 january 2009 michael a. radecki c changed address of vendor b. 1 july 2010 michael a. radecki d removed an approved source of supply. 12 june 2013 michael a. radecki prepared in accordance with asme y14.100 rev status of pages rev d d d d d d d d pages 1 2 3 4 5 6 7 8 pmic n/a prepared by michael a. radecki design activity defense supply center, columbus columbus, oh original date of drawing 3 january 200 5 checked by michael a. radecki title capacitors, fixed, ceramic, chip, 0 805 , high frequency , bp approved by kendall a. cottongim size a code ident. no. 037z3 dwg no. 0 5001 rev d page 1 of 8 amsc n/a 5910- 2013 - e 14 current design activity cage code 037z3 has changed names to: dla land and maritime columbus, ohio 43218 - 3990
defense supply center, columbus columbus, ohio size a code ident no. 037z3 dwg no. 05001 rev d page 2 1. scope 1.1 scope . this drawing and mil - prf -55681 describe the requirements for ceramic, chip. 1.2 part or identifying number (pin) the complete pin is as follows: 0 5001 - 2r0 b c z - drawing number capacitance value (see 1.2.1) voltage (see 1.2.2) capacitance tolerance (see 1.2.3) termination finish (see 1.2.4) group c testing option (see 1.2.5 ) 1.2. 1 capacitance value . the nominal capacitance value, expressed in picofarads (pf) is identified by a three digit number; the first two digits represent significant figures and the last digit specifies the number of zeros to follow. when the nominal value is less than 10 pf, the letter ?r? is used to indicate the decimal point and the succeeding digit(s) of the group represent significant figur e(s). 1r0 indicates 1.0 pf; r75 indicates .75 pf; and 0r5 indicates 0.5 pf. see table iv for values. 1.2.2 voltage . the rated voltage for continuous operation at +125 c is identified by a single letter as shown in table i. table i. rated voltage . symbol rated voltage (volts, dc) z 25 a 50 b 100 c 200 k 250 1.2. 3 capacitance tolerance . the capacitance tolerance is identified by a single letter in accordance with table ii. table ii. capacitance tolerance . symbol capacitance tolerance () a .05 pf b .1 pf c .25 pf d .50 pf f 1 percent g 2 percent j 5 percent k 10 percent m 20 percent 1.2.4 termination finish . termination finish is identified by a single letter as shown in table iii. table iii. termination finish . symbol termination finish m palladium - silver z base metallization - barrier metal - tinned (tin/lead alloy, with a minimum of 4 percent lead)
defense supply center, columbus columbus, ohio size a code ident no. 037z3 dwg no. 05001 rev d page 3 1.2.5 group c testing option . to require mil - prf - 55681 group c testing, use the appropriate letter from the table below. if group c testing is not desired, leave this location blank. note: ordering group c options that c ontain a 2,000 hour life test may extend the processing time by 90 days or more. letter group c testing option c full group c l 2,000 hour life test only m 1,000 hour life test only h low voltage humidity only n/a no group c testing. 2. applicable documents 2.1 general . the documents listed in this section are specified in sections 3 and 4 of this specification. this section does not include documents cited in other sections of this specification or recommended for additional information or as examples. while every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 government documents . 2. 2 .1 specifications , standards , and handbooks . the following specifications, standards, and handbooks form a part of this document to the extent specified herein. unless otherwise specified, the issues of these documents are those cited in the so licitation or contract (see 6.2 ). department of defense specifications mil - prf -55681 - capacitor, chip, multiple layer, fixed, unencapsulated, ceramic dielectric, established reliability and non - established reliability, general specification for. department of defense standards mil - std -202 - electronic and electrical component parts, test methods for. mil - std -1285 - marking of electrical and electronic parts. (copies of these documents are available online at http://quicksearch.dla.mil/ from the standardization document order desk, 700 robbins avenue, build ing 4d, philadelphia, pa 19111 - 5094.) 2. 3 order of precedence. unless otherwise noted herein or in the contract, i n the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. requirements 3.1 item requirements . the individual item requirements shall be in accordance with mil - prf -55681 , and as specified herein. these capacitors shall b e capable of meeting all electrical, environmental, and mechanical requirements of mil - prf - 55681 , unless otherwise stated. 3.2 interface and physical dimensions . the interface and physical dimensions shall be as specified in mil - prf - 55681 and herein (see figure 1 ). 3.2.1 tin plated finishes . tin plating is prohibited as a final finish or as an undercoat. tin - lead (sn- pb) finishes are acceptable provided that the minimum lead content is 4 percent (see 6.4 ).
defense supply center, columbus columbus, ohio size a code ident no. 037z3 dwg no. 05001 rev d page 4 t w y l notes: 1. dimensions are in inches. 2. metric equivalents are given for general information only. figure 1. case dimensions and configuration . 3.3 electrical characteristics . 3.3.1 dielectric type . the dielectric type shall be bp ( 30 ppm/ c) ceramic in accordance with mil - prf -55681 . 3.3.2 capacitance . capacitance shall be in accordance with table iv when measured in accordance with method 305 of mil - std - 202 . the following conditions shall apply: 1,000 pf 1 mhz 50 khz 1 v rms .2 v rms > 1,000 pf 1 khz 50 hz 1 v rms .2 v rms inches mm .008 0. 20 .010 0. 25 .02 0 0. 5 1 .049 1.24 .055 1. 4 0 .079 2.00 dimensions l .00 8 w .0 08 t max y .0 1 .0 79 .0 49 .0 5 5 .0 20
defense supply center, columbus columbus, ohio size a code ident no. 037z3 dwg no. 05001 rev d page 5 3.3.3 dissipation factor (+25 c) . when measured at the frequency and voltage specified in 3.3.2 , t he dissipa tion factor shall be 0.05 percent. 3.3.4 insulation resistance . at +25 c: minimum of 100,000 megohms or 1,000 megohm - microfarads, whichever is less. at +125 c: minimum of 1,000 megohms or 10 megohm - microfarads, whichever is less. 3.4 solderability . in accordance with mil - prf -55681 , except the sample size shall be 5 pieces with zero defectives permitted. 3.5 moisture resistance . in accordance with mil - prf - 55681 , with the following exceptions: a. polarizing voltage shall be rated vo ltage. b. testing may be performed on chips with a larger width and/or length as long as they are cut from the same wafer(s) as tho se used for production. 3.6 marking . as a minimum, marking shall be on the package due to the small size of the chips. the package marking shall be in accordance with mil - std -1285 , except the pin shall be as specified in paragraph 1.2 with manufacturer?s name or cage code and date code. the manufacturer may, at their option, mark some information o n the chips. suggested marking is the 2 digit eia capacitance code. 3.7 manufacturer eligibility . to be eligible for listing as a n approved source of supply, a manufacturer shall be listed on the mil - prf - 55681 qualified products list for at least one part, or perform the group a and group c inspections specified herein on a sample of parts agreed upon by the manufacturer and dla land and maritime -va. 3.8 certificate of compliance . a certificate of compliance shall be required from manufacturers requesting to be a n approved source of supply. 3.9 recycled, recovered, or environmentally preferable materials . recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requiremen ts, and promotes economically advantageous life cycle costs. 3.10 workmanship . in accordance with mil - prf - 55681 . 4. verification 4.1 qualification inspection . qualificatio n inspection is not required. 4.2 conformance inspection . 4.2.1 inspection of product for delivery . inspection of product for delivery shall consist of all tests specified in group a of mil - prf -55681 . esr testing and ppm testing and calculation are not applicable. when optional group c testing is requested, termi nal strength and series resonance are not applicable. 5. packaging 5.1 packaging . for acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2 ). when packaging of materiel is to be performed by dod or in - house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. packaging requirements are maintained by the inventory control point ?s packaging activities within the military serv ice or defense agency, or within the military service?s system commands. packaging data retrieval is available from the managing military department?s or defense agency?s automated packaging files, cd - rom products, or by contacting the responsible packagi ng activity.
defense supply center, columbus columbus, ohio size a code ident no. 037z3 dwg no. 05001 rev d page 6 6. notes (this section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 intended use . capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for oem application. this drawing is intended exc lusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog list ings. when a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new de sign. 6.2 ordering data . the contract or purchase order should specify the f ollowing: a. complete pin (see 1.2 ). b. requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have pas sed conformance insp ection with each shipment of parts by the manufacturer. c. requirements for notification of change of product to acquiring activity, if applicable. d. requirements for packaging and packing. 6.3 replaceability . capacitors covered by this drawing will replace the same commercial device covered by a contractor - prepared specification or drawing. 6.4 tin whisker growth . the use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. t in whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. conformal coatings applied over top of a whisker - prone surface will not prevent the formation of t in whiskers. alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. for additional informatio n on this matter, refer to astm - b545 (standard specification for electrodeposited coatings of tin). 6. 5 users of record . coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. requests to be ad ded as a recorded user of this drawing may be achieved online at capacitorfilter@dla.mil or if in writing to: dla land and maritime , attn: vat, post office box 3990, columbus, oh 4321 8 -399 0 or by telephone (614) 692 - 4709 or dsn 850 - 4709. 6. 6 approved sources of supply . approved sources of supply are listed herein. additional sources will be added as they become available. a ssistance in the use of this drawing may be obtained online at capacitorfilter@dla.mil or by contact ing dla land and maritime , attn: vat, p ost office box 3990, columbus, oh 4321 8 -399 0 or by telephone (614) 692 - 4709 or dsn 850 - 4709 . 6.7 changes from previous issue . the margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. this was done as a convenience only and the government assumes no liability whatsoever for any inaccuracies in these notations. bidders and contract ors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue.
defense supply center, columbus columbus, ohio size a code ident no. 037z3 dwg no. 05001 rev d page 7 t able iv. el ectrical characteristics . dscc drawing 0500 1 - 1 / capacitance pf available tolerances a tc vendor a available voltages vishay 2 / vendor b available voltages z a b c k z a b c k 25 50 100 200 250 25 50 100 200 250 0r1 - - - - .1 a, b 0r2 - - - - .2 a, b 0r3 - - - - .3 a, b, c 0r4 - - - - .4 a, b, c 0r5 - - - - .5 a, b, c 0r6 - - - - .6 a, b, c 0r7 - - - - .7 a, b, c 0r8 - - - - .8 a, b, c 0r9 - - - - .9 a, b, c 1r0 - - - - 1 a, b, c 1r1 - - - - 1.1 a, b, c, d 1r2 - - - - 1.2 a, b, c, d 1r3 - - - - 1.3 a, b, c, d 1r4 - - - - 1.4 a, b, c, d 1r5 - - - - 1.5 a, b, c, d 1r6 - - - - 1.6 a, b, c, d 1r7 - - - - 1.7 a, b, c, d 1r8 - - - - 1.8 a, b, c, d 1r9 - - - - 1.9 a, b, c, d 2r0 - - - - 2 a, b, c, d 2r1 - - - - 2.1 a, b, c, d 2r2 - - - - 2.2 a, b, c, d 2r4 - - - - 2.4 a, b, c, d 2r7 - - - - 2.7 a, b, c, d 3r0 - - - - 3 a, b, c, d 3r3 - - - - 3.3 a, b, c, d 3r6 - - - - 3.6 a, b, c, d 3r9 - - - - 3.9 a, b, c, d 4r3 - - - - 4.3 a, b, c, d 4r7 - - - - 4.7 a, b, c, d 5r1 - - - - 5.1 a, b, c, d 5r6 - - - - 5.6 a, b, c, d 6r2 - - - - 6.2 a, b, c, d 6r8 - - - - 6.8 b, c, j, k, m 7r5 - - - - 7.5 b, c, j, k, m 8r2 - - - - 8.2 b, c, j, k, m 9r1 - - - - 9.1 b, c, j, k, m 100 - - - - 10 f, g, j, k, m 110 - - - - 11 f, g, j, k, m 120 - - - - 12 f, g, j, k, m 130 - - - - 13 f, g, j, k, m 150 - - - - 15 f, g, j, k, m 180 - - - - 18 f, g, j, k, m 200 - - - - 20 f, g, j, k, m 220 - - - - 22 f, g, j, k, m 240 - - - - 24 f, g, j, k, m 270 - - - - 27 f, g, j, k, m 300 - - - - 30 f, g, j, k, m 330 - - - - 33 f, g, j, k, m see footnote at end of table .
defense supply center, columbus columbus, ohio size a code ident no. 037z3 dwg no. 05001 rev d page 8 t able iv. electrical characteristics . ? continued. dscc drawing 0500 1 - 1 / capacitance pf available tolerances a tc vendor a available voltages vishay 2 / vendor b available voltages z a b c k z a b c k 25 50 100 200 250 25 50 100 200 250 360 - - - - 36 f, g, j, k, m 390 - - - - 39 f, g, j, k, m 430 - - - - 43 f, g, j, k, m 470 - - - - 47 f, g, j, k, m 510 - - - - 51 f, g, j, k, m 560 - - - - 56 f, g, j, k, m 620 - - - - 62 f, g, j, k, m 680 - - - - 68 f, g, j, k, m 750 - - - - 75 f, g, j, k, m 820 - - - - 82 f, g, j, k, m 910 - - - - 91 f, g, j, k, m 101 - - - - 100 f, g, j, k, m 1 / complete pin shall include symbols to indicate voltage, capacitance tolerance, termination finish, and group c testing option (see 1.2 ). 2 / vendor does not supply tolerance ?a? ( .05pf). vendor vendor cage vendor name and address similar designation 1 / a 29990 3q6g1 american technical ceramics corporation one norden lane huntington station, ny 11746 - 2141 plant: 2201 corporate square boulevard jacksonville, fl 32216 - 1921 600f****w250 b shv71 vishay specialty capacitors ramat gabriel p.o. box 852 migdal haemek 10500 israel vj0805*******a*7q 1 / parts must be purchased to the dscc pin to assure that all performance requirements and tests are met.
|
